Robinson Tuition
Physics Paper 1 · Particle model of matter · free required practical sheet

Density of solids and liquids

Aligned to AQA Combined Science 8464 and AQA GCSE Physics 8463

To find the density of regular solids, irregular solids and a liquid by measuring their mass and volume.

14 original questions, 36 marks. Try each one, then open the model answer and mark yourself against the marking points. Or print the sheet and mark it with the answers sheet. The full method is in the revision notes at the bottom.

Practical sheet PDFAnswers and revision notes PDF

The results

Equipment: Top-pan balance (reading to 0.1 g); Ruler marked in mm, or vernier callipers; Regularly shaped solids (for example a metal cuboid and cube); Irregular objects (for example a pebble and a rubber stopper); Displacement (eureka) can; Measuring cylinders (10 cm3, 50 cm3 and 100 cm3); Beaker of water; Thread; The liquid to be tested (for example cooking oil); Paper towels.

Ruby found the mass and volume of five objects. She has not finished the brass cube row, so two values are shown as X and Y, and the pebble's density is shown as Z.

ObjectHow the volume was foundMass in gVolume in cm3Density in g/cm3
Aluminium block, 5.0 cm × 3.0 cm × 2.0 cmRuler81.330.02.71
Brass cube, each side 2.0 cmRuler68.0XY
Granite pebbleDisplacement can48.618.5Z
Rubber stopperMeasuring cylinder22.815.01.52
Glass marbleMeasuring cylinder12.55.02.50

The questions

1

Name the measuring instrument Ruby should use to find:

  1. the mass of the aluminium block
  2. the length of each side of the block.
2 marks
Show the model answer

a) A top-pan balance.

b) A ruler marked in millimetres (or vernier callipers).

Marking points
  • Balance (top-pan or electronic)
  • Ruler (mm scale) or callipers
2

Describe how Ruby used the displacement can to find the volume of the granite pebble.

2 marks
Show the model answer

She filled the can with water until it ran out of the spout and waited for the dripping to stop. Then she put an empty measuring cylinder under the spout, lowered the pebble in gently on a thread, and read the volume of water collected in the cylinder. This volume equals the volume of the pebble.

Marking points
  • Fill the can to the spout (until dripping stops) before adding the pebble
  • Collect the displaced water in a measuring cylinder: its volume is the pebble's volume
3

Explain how Ruby should read the measuring cylinder to get an accurate volume.

2 marks
Show the model answer

She should put the cylinder on a flat bench and read the scale at the bottom of the curved surface of the water (the meniscus), with her eye level with it. Looking from above or below would give a parallax error.

Marking points
  • Read at the bottom of the meniscus
  • Eye level with the surface to avoid parallax error
4

Give one hazard in this practical and describe how to reduce the risk.

2 marks
Show the model answer

Water spilling from the displacement can could make the floor slippery. Ruby should stand the can in a tray and wipe up any spills straight away.

Marking points
  • Hazard: spilled water (slips, near the balance), dropped heavy block, or broken glass
  • Matching control, e.g. tray and wipe spills, lower objects on a thread, use plastic cylinders
5

Calculate the values of X and Y for the brass cube. Show your working.

3 marks
Show the model answer

X: volume = 2.0 × 2.0 × 2.0 = 8.0 cm3.

Y: density = 68.0 ÷ 8.0 = 8.5 g/cm3.

volume = length × width × height
volume = 2.0 × 2.0 × 2.0
X = 8.0 cm3
density = mass ÷ volume
density = 68.0 ÷ 8.0
Y = 8.5 g/cm3
Marking points
  • Volume = 2.0 × 2.0 × 2.0
  • X = 8.0 cm3
  • Y = 8.5 g/cm3
6

Calculate the value of Z, the density of the granite pebble. Give your answer to 3 significant figures.

2 marks
Show the model answer

Density = 48.6 ÷ 18.5 = 2.627 g/cm3, which is 2.63 g/cm3 to 3 significant figures.

density = mass ÷ volume
density = 48.6 ÷ 18.5
density = 2.627 g/cm3
Z = 2.63 g/cm3 (3 s.f.)
Marking points
  • Density = 48.6 ÷ 18.5
  • 2.63 g/cm3
7

Mohammed measured the density of cooking oil. He wrote down:

mass of empty measuring cylinder = 62.4 g
mass of measuring cylinder with oil = 108.4 g
volume of oil = 50.0 cm3

Calculate the density of the cooking oil. Show your working.

3 marks
Show the model answer

Mass of oil = 108.4 - 62.4 = 46.0 g.

Density = 46.0 ÷ 50.0 = 0.92 g/cm3.

mass of oil = 108.4 - 62.4
mass of oil = 46.0 g
density = mass ÷ volume
density = 46.0 ÷ 50.0
density = 0.92 g/cm3
Marking points
  • Subtracts the cylinder: mass of oil = 46.0 g
  • Density = 46.0 ÷ 50.0
  • 0.92 g/cm3
8

The density of the aluminium block is 2.71 g/cm3. Write this density in kg/m3.

2 marks
Show the model answer

1 g/cm3 = 1000 kg/m3, so 2.71 × 1000 = 2710 kg/m3.

1 g/cm3 = 1000 kg/m3
density = 2.71 × 1000
density = 2710 kg/m3
Marking points
  • Multiplies by 1000
  • 2710 kg/m3
9

Higher tier

A brass weight is a cuboid measuring 45 mm by 30 mm by 12 mm. Its mass is 0.137 kg.

Calculate its density in kg/m3. Give your answer to 3 significant figures. Show your working.

4 marks
Show the model answer

In metres the sides are 0.045 m, 0.030 m and 0.012 m.

Volume = 0.045 × 0.030 × 0.012 = 1.62 × 10-5 m3.

Density = 0.137 ÷ (1.62 × 10-5) = 8457 kg/m3, which is 8460 kg/m3 to 3 significant figures.

45 mm = 0.045 m
30 mm = 0.030 m
12 mm = 0.012 m
V = 0.045 × 0.030 × 0.012
V = 1.62 × 10-5 m3
ρ = m ÷ V
ρ = 0.137 ÷ (1.62 × 10-5)
ρ = 8456.8 kg/m3
ρ = 8460 kg/m3 (3 s.f.)
Marking points
  • Converts lengths to metres
  • Volume = 1.62 × 10-5 m3
  • Density = mass ÷ volume
  • 8460 kg/m3
10

Ruby measured the volume of the pebble three times with the displacement can. She got 18.5 cm3, 18.0 cm3 and 19.0 cm3.

Calculate the mean volume and say whether her readings are repeatable.

2 marks
Show the model answer

Mean = (18.5 + 18.0 + 19.0) ÷ 3 = 18.5 cm3. The readings are close together (within 1.0 cm3 of each other), so they are repeatable.

Marking points
  • Mean = 18.5 cm3
  • Repeatable, because the readings are close together (small spread)
11

Ruby's first try with the displacement can gave a pebble volume that was too small. Suggest one reason why, and how she could stop it happening.

2 marks
Show the model answer

She may not have filled the can right up to the spout, so the first water pushed up just filled the can instead of coming out. She should fill it until it overflows and wait for the dripping to stop before putting the cylinder under the spout.

Marking points
  • A sensible reason: can not full to the spout, drops left in the spout, water splashed out when the pebble was dropped in
  • A matching fix: fill until it drips and wait, lower the pebble gently on a thread, tap the spout
12

Higher tier

Ruby measured each side of the 2.0 cm brass cube with a ruler marked in millimetres. Explain why her value for its density could be quite far from the true value, and suggest a better instrument.

2 marks
Show the model answer

The ruler's resolution is 1 mm, which is 5% of a 20 mm side, and the volume uses the side three times, so a small error in reading each length becomes a large error in the volume and so the density. Vernier callipers or a micrometer have a much smaller resolution (0.1 mm or less), so the volume is more accurate.

Marking points
  • Resolution of 1 mm is large compared with a 20 mm side, and the error is multiplied three times in the volume
  • Use vernier callipers or a micrometer (smaller resolution)
13

Ruby wants to find the volume of a cork using a measuring cylinder of water. The cork floats. Describe how she could still find its volume.

2 marks
Show the model answer

Tie the cork to a heavy sinker, such as a metal nut. First lower just the sinker into the water and read the volume. Then lower the sinker and cork together until both are under the water and read again. The difference between the two readings is the volume of the cork.

Marking points
  • Use a sinker (or push it under with a thin pin) so the cork is fully under water
  • Volume of cork = reading with cork and sinker - reading with sinker only
14

Plan an investigation to find out how the density of salt water depends on the mass of salt dissolved in it.

6 marks
Show the model answer

Measure 100 cm3 of water into a beaker with a measuring cylinder. Weigh out 5 g of salt on a balance, add it to the water and stir until it has all dissolved. Repeat to make solutions with 0 g, 10 g, 15 g, 20 g and 25 g of salt in 100 cm3 of water. For each solution, put an empty 50 cm3 measuring cylinder on the balance and press tare. Pour in the salt water until the bottom of the meniscus is on the 50.0 cm3 mark, reading with my eye level with it, and record the mass of the liquid shown on the balance. Calculate density = mass ÷ volume. Rinse and dry the cylinder between solutions and keep all the solutions at room temperature. Repeat each measurement three times and find the mean density. Plot a graph of density against mass of salt to see the pattern; I would expect the density to increase as more salt is dissolved. Wipe up any spills so no one slips and the balance stays dry.

Marking points (any 6, with the method in a logical order)
  • Same volume of water for each solution, measured with a measuring cylinder
  • Measure different masses of salt on a balance and dissolve completely
  • Tare the balance with the empty cylinder (or subtract its mass)
  • Measure a fixed volume of each solution, reading the meniscus at eye level
  • Record the mass of the solution only
  • Calculate density = mass ÷ volume
  • Keep temperature the same; rinse and dry the cylinder between solutions
  • Repeat and calculate a mean for each solution
  • Plot density against mass of salt, or a sensible safety point
How it is marked
  • 5-6 marks: a clear, logical plan that makes a range of solutions, measures the mass and volume of each correctly, calculates density and says how the results will be compared.
  • 3-4 marks: a workable plan to measure mass and volume of the solutions, but parts are missing, such as how the cylinder's mass is removed or which variables are kept the same.
  • 1-2 marks: some relevant steps such as weighing or measuring volume, but no clear sequence and it would not give a density for each solution.

Revision notes: the method in full

Aim: To find the density of regular solids, irregular solids and a liquid by measuring their mass and volume.

Equipment

  • Top-pan balance (reading to 0.1 g)
  • Ruler marked in mm, or vernier callipers
  • Regularly shaped solids (for example a metal cuboid and cube)
  • Irregular objects (for example a pebble and a rubber stopper)
  • Displacement (eureka) can
  • Measuring cylinders (10 cm3, 50 cm3 and 100 cm3)
  • Beaker of water
  • Thread
  • The liquid to be tested (for example cooking oil)
  • Paper towels

Method

  1. Regular solid: measure its mass on the balance.
  2. Measure its length, width and height with a ruler (or callipers), and work out the volume as length × width × height.
  3. Irregular solid that fits in a measuring cylinder: half fill the cylinder with water and read the volume at the bottom of the meniscus, with your eye level with it.
  4. Tie the object to a thread, lower it gently into the water until it is covered, and read the new volume; the difference is the volume of the object.
  5. Larger irregular solid: fill a displacement can with water until it drips from the spout, wait for it to stop, and put an empty measuring cylinder under the spout.
  6. Lower the object gently into the can on a thread and collect all the water that comes out; its volume is the volume of the object.
  7. Measure the mass of each object on the balance, drying it first if it has been in water.
  8. Liquid: put an empty measuring cylinder on the balance and press tare (or record its mass).
  9. Pour in a measured volume of the liquid, such as 50.0 cm3, and record the mass of the liquid alone.
  10. Calculate each density using density = mass ÷ volume, and repeat each measurement to find a mean.

Variables

  • Independent: The object or liquid being tested.
  • Dependent: The density, calculated from the mass (balance) and the volume (ruler, measuring cylinder or displacement can).
  • Control: Use water at room temperature in the cylinder and can; Fill the displacement can to the spout every time; Read every measuring cylinder at the bottom of the meniscus, at eye level; Use the same balance, zeroed before each reading

Hazards

HazardWhat could happenHow to reduce the risk
Spilled water on the floor or benchSomeone slips, or water reaches the electric balanceStand the displacement can in a tray, wipe up spills straight away and keep the balance away from the water.
Heavy metal blocksInjury to feet or breaking glassware if droppedLower objects gently on a thread and keep them near the middle of the bench.
Glass measuring cylindersCuts if one is knocked over and breaksUse plastic cylinders where possible and do not drop objects into them.

Key points

  • Density = mass ÷ volume; in g/cm3 use grams and cm3, in kg/m3 use kg and m3.
  • To change g/cm3 to kg/m3, multiply by 1000.
  • For a liquid, subtract the mass of the empty cylinder (or tare it): you want the mass of the liquid only.
  • Volume by displacement = new reading - starting reading, not the new reading on its own.
  • Read measuring cylinders at the bottom of the meniscus with your eye level with it.
  • Wait for the displacement can to stop dripping before you start and after you add the object.

Every question and data set here is original and written by Robinson Tuition. Aligned to AQA Combined Science 8464 and AQA GCSE Physics 8463; this is not an exam-board paper and is not endorsed by AQA.