Name the salt made when copper(II) oxide reacts with sulfuric acid.
Show the model answer
Copper(II) sulfate.
- Copper(II) sulfate (copper sulfate accepted)
Aligned to AQA Combined Science 8464 and AQA GCSE Chemistry 8462
To make pure, dry crystals of a soluble salt (copper(II) sulfate) by reacting an insoluble metal oxide with a dilute acid.
14 original questions, 35 marks. Try each one, then open the model answer and mark yourself against the marking points. Or print the sheet and mark it with the answers sheet. The full method is in the revision notes at the bottom.
Equipment: 25 cm3 measuring cylinder; 100 cm3 beaker; dilute sulfuric acid; copper(II) oxide powder; spatula and glass rod; Bunsen burner, tripod, gauze and heatproof mat; filter funnel and filter paper; conical flask; evaporating basin and water bath; balance; safety goggles.
Five groups in Mr Okafor's class each warmed 25 cm3 of the same sulfuric acid and added 1.50 g of copper(II) oxide. After filtering, each group dried and weighed the unreacted copper(II) oxide left on the filter paper. A week later they weighed their dry crystals.
| Group | Mass of copper(II) oxide added in g | Mass of unreacted copper(II) oxide on filter paper in g | Mass of dry crystals in g |
|---|---|---|---|
| A | 1.50 | 0.52 | 2.61 |
| B | 1.50 | 0.49 | 2.48 |
| C | 1.50 | 0.55 | 2.55 |
| D | 1.50 | 0.51 | 1.37 |
| E | 1.50 | 0.50 | 2.66 |
Name the salt made when copper(II) oxide reacts with sulfuric acid.
Copper(II) sulfate.
Explain how a pupil can tell that the copper(II) oxide is in excess.
Black solid is left at the bottom of the beaker and does not disappear even after stirring. This means there is no acid left to react with it.
Give two variables the groups kept the same so that their masses of crystals could be compared fairly.
The volume of sulfuric acid (25 cm3) and the concentration of the acid.
During evaporation, one pupil heats the basin strongly until the solution boils hard. Give one hazard of doing this and one way to reduce the risk.
Hot solution can spit out of the basin and burn the skin or get in the eyes. Heat gently, for example over a water bath, wear goggles and stop heating once crystals start to appear.
Explain why the mixture is filtered before it is evaporated.
Filtering removes the excess copper(II) oxide, which is insoluble. If it was left in, the crystals would be contaminated with black powder, so the salt would not be pure.
Use the table to calculate the mass of copper(II) oxide that reacted for Group A.
0.98 g
Which group's mass of crystals is anomalous? Suggest one reason for this result, and say what the class should do with it.
Group D, because 1.37 g is much lower than the others, which are all about 2.5 g. They may have spilt some of the filtrate, or they may not have waited long enough for all the crystals to form. The class should leave it out when working out the mean.
Calculate the mean mass of dry crystals made by the class. Do not include the anomalous result. Give your answer to 2 decimal places. Show your working.
2.58 g
Calculate the percentage of the copper(II) oxide added by Group A that reacted with the acid. Use your answer to question 6. Give your answer to 2 significant figures. Show your working.
65%
The masses of unreacted copper(II) oxide are all close to 0.5 g. Explain what this tells you about the amount of acid each group used, and why Group D's low mass of crystals was not caused by using less acid.
Each group had about the same amount of copper(II) oxide react, about 1.0 g. This suggests that every group used the same amount of acid, because the acid is what runs out first. Group D's unreacted mass (0.51 g) is normal, so the same amount of salt was made in their solution and the crystals must have been lost later, during filtering, evaporating or drying.
Write a balanced symbol equation, with state symbols, for the reaction between copper(II) oxide and sulfuric acid.
CuO(s) + H2SO4(aq) → CuSO4(aq) + H2O(l)
Higher tier
Kwame says the crystals would be larger if he evaporated all the water quickly on a hot gauze. Explain why he is wrong.
Fast evaporation makes lots of tiny crystals form at once, or just a powder. Slow evaporation at room temperature gives the particles time to join on to a few growing crystals, so the crystals end up larger.
Group B's crystals still looked wet when they weighed them. Explain what effect this has on their mass, and suggest how they could improve their method.
The water adds to the mass, so their result is higher than the true mass of crystals. They should pat the crystals dry between filter paper and leave them in a warm place until two weighings give the same mass.
Describe how you would make pure, dry crystals of zinc chloride from zinc carbonate powder and dilute hydrochloric acid.
Measure about 25 cm3 of dilute hydrochloric acid into a beaker with a measuring cylinder and wear goggles. Add zinc carbonate a spatula at a time and stir. It will fizz because carbon dioxide is made. Keep adding until the fizzing stops and some white powder stays undissolved at the bottom, which shows the zinc carbonate is in excess and all the acid has reacted. Filter the mixture through filter paper into a conical flask to remove the excess zinc carbonate. Pour the clear filtrate into an evaporating basin and heat it gently until about half the water has gone and crystals start to appear. Do not heat it to dryness. Leave the basin somewhere warm for a few days so the rest of the water evaporates slowly. Finally, pat the crystals dry with filter paper.
Aim: To make pure, dry crystals of a soluble salt (copper(II) sulfate) by reacting an insoluble metal oxide with a dilute acid.
Equipment
Method
Variables
Hazards
| Hazard | What could happen | How to reduce the risk |
|---|---|---|
| Dilute sulfuric acid | Can irritate the eyes and skin | Wear safety goggles and wash any splashes off skin straight away |
| Copper(II) sulfate solution and crystals | Harmful if swallowed and irritates the eyes | Wear goggles, do not taste, wash hands after the lesson |
| Hot basin and boiling solution | Burns, or hot solution spitting out of the basin | Heat gently, stop before the solution is dry, and use tongs to move the basin |
Key points
Every question and data set here is original and written by Robinson Tuition. Aligned to AQA Combined Science 8464 and AQA GCSE Chemistry 8462; this is not an exam-board paper and is not endorsed by AQA.