Aligned to AQA GCSE Chemistry 8462 only (not Combined Science)
To find the volume of an acid that exactly neutralises a measured volume of an alkali, and use it to work out the concentration of the alkali.
14 original questions, 35 marks. Try each one, then open the model answer and mark yourself against the marking points. Or print the sheet and mark it with the answers sheet. The full method is in the revision notes at the bottom.
Equipment: burette and clamp stand; 25.0 cm3 volumetric pipette and pipette filler; conical flask; small funnel; white tile; dilute hydrochloric acid of known concentration; sodium hydroxide solution of unknown concentration; indicator (phenolphthalein or methyl orange); safety goggles.
Priya titrated 25.0 cm3 portions of sodium hydroxide solution with 0.100 mol/dm3 hydrochloric acid, using phenolphthalein. She did one rough run and four accurate runs.
Titration
Start burette reading in cm3
Final burette reading in cm3
Titre in cm3
Rough
0.00
23.55
23.55
1
23.55
46.75
23.20
2
0.50
23.45
22.95
3
1.20
24.10
?
4
0.30
23.25
22.95
The questions
1
Name the piece of equipment used to measure the 25.0 cm3 of sodium hydroxide, and explain why it is used instead of a measuring cylinder.
2 marks
Show the model answer
A volumetric pipette (with a pipette filler). It measures one fixed volume much more accurately than a measuring cylinder.
Marking points
Volumetric pipette
More accurate / smaller uncertainty than a measuring cylinder
2
Give two reasons why the conical flask is placed on a white tile and swirled during the titration.
2 marks
Show the model answer
The white tile makes the colour change of the indicator easier to see. Swirling mixes the acid with the alkali so the colour change is not reached too early in one part of the flask.
Marking points
White tile: colour change easier to see
Swirling: mixes the reactants so the end point is accurate
3
Give two things Priya must keep the same in each accurate titration, other than the concentration of the acid.
2 marks
Show the model answer
The volume of sodium hydroxide (25.0 cm3) and the indicator used, with the same number of drops.
Marking points
Volume of alkali
Indicator type / number of drops (or judging the same end point colour)
4
Dilute hydrochloric acid is an irritant. Describe one hazard when filling the burette with the acid and how to reduce the risk.
2 marks
Show the model answer
Liquid can splash or overflow into the eyes when pouring above eye level. Fill the burette below eye level using a small funnel, pour slowly, and wear safety goggles.
Marking points
Splashing / overflowing into eyes or onto skin
Fill below eye level with a funnel / pour slowly / wear goggles
5
Calculate the titre for titration 3.
1 mark
Show the model answer
22.90 cm3
Titre = final reading - start reading
Titre = 24.10 - 1.20 = 22.90 cm3
Marking points
22.90 cm3
6
Which accurate titrations are concordant? Explain your answer.
2 marks
Show the model answer
Titrations 2, 3 and 4 (22.95, 22.90 and 22.95 cm3). They are all within 0.10 cm3 of each other. Titration 1 (23.20 cm3) is 0.25 cm3 higher, so it is not concordant.
Marking points
Titrations 2, 3 and 4
They are within 0.10 cm3 of each other; titration 1 is not
7
Calculate the mean titre using only the concordant results. Give your answer to 2 decimal places. Show your working.
3 marks
Show the model answer
22.93 cm3
Concordant titres: 22.95, 22.90, 22.95
Total = 22.95 + 22.90 + 22.95 = 68.80 cm3
Mean = 68.80 / 3 = 22.933...
Mean titre = 22.93 cm3
Marking points
Uses titrations 2, 3 and 4 only
(22.95 + 22.90 + 22.95) / 3
22.93 cm3
8
Suggest why the rough titre is larger than the accurate ones, and why it is not used in the mean.
2 marks
Show the model answer
In the rough run the acid is added quickly, so it is easy to go past the end point and add too much. It is only a guide to where the end point is, so it is not accurate enough to include.
Marking points
Acid added quickly so the end point is overshot
It is only a guide / not accurate enough to include
9
Higher tier
Use your mean titre from question 7 to calculate the number of moles of hydrochloric acid that reacted. The acid concentration is 0.100 mol/dm3.
2 marks
Show the model answer
0.002293 mol (2.293 x 10-3 mol)
Volume = 22.93 / 1000 = 0.02293 dm3
Moles = concentration x volume
Moles = 0.100 x 0.02293
Moles of HCl = 0.002293 mol
Marking points
Volume converted to dm3: 22.93 / 1000 = 0.02293
0.002293 mol
10
Higher tier
The equation is NaOH + HCl → NaCl + H2O. Use your answer to question 9 to calculate the concentration of the sodium hydroxide solution in mol/dm3. Give your answer to 3 significant figures. Show your working.
3 marks
Show the model answer
0.0917 mol/dm3
Ratio NaOH : HCl = 1 : 1, so moles of NaOH = 0.002293 mol
Convert your answer to question 10 into a concentration in g/dm3. The relative formula mass (Mr) of NaOH is 40.
2 marks
Show the model answer
3.67 g/dm3
Mass concentration = concentration in mol/dm3 x Mr
Mass concentration = 0.09172 x 40 = 3.6688
Mass concentration = 3.67 g/dm3
Marking points
0.0917 x 40
3.67 g/dm3 (3.7 accepted)
12
Oliver forgot to remove the air bubble from the tip of his burette, and it came out during his first accurate titration. Explain the effect on his titre, and say how he should have avoided it.
3 marks
Show the model answer
The burette reading changes as the bubble leaves, but no acid has gone into the flask for that volume. So his titre would be too large. Before taking the start reading, he should open the tap and run a little acid into a waste beaker until the tip is completely full of liquid.
Marking points
Titre recorded is too large
Because the bubble's volume is counted as acid added when it was not
Run some acid through the tap before the start reading so the tip is filled
13
Burette readings are recorded to the nearest 0.05 cm3. Explain the difference between the results being precise and being accurate, using Priya's titres as an example.
3 marks
Show the model answer
Precise means the repeat results are close together: titres 2, 3 and 4 are within 0.05 cm3 of each other, so they are precise. Accurate means close to the true value. The results could be precise but still inaccurate if, for example, the acid was not exactly 0.100 mol/dm3, because every titre would be wrong by the same amount.
Marking points
Precise = repeats close together / little spread
Accurate = close to the true value
Example: concordant titres are precise, but a systematic error (wrong acid concentration, misread meniscus every time) could make them inaccurate
14
A school has a bottle of dilute sulfuric acid with no label for its concentration. A technician has potassium hydroxide solution of known concentration. Plan a titration to find the volume of the potassium hydroxide solution that exactly neutralises 25.0 cm3 of the acid.
6 marks
Show the model answer
Wear goggles. Use a pipette and pipette filler to put exactly 25.0 cm3 of the sulfuric acid into a conical flask, and add a few drops of methyl orange, which is red in acid. Rinse a burette with potassium hydroxide solution, fill it using a funnel below eye level, and run a little through so there is no air bubble. Record the start reading at the bottom of the meniscus. Put the flask on a white tile and add the alkali while swirling until the indicator turns yellow; this is the rough titre. Repeat with fresh acid, adding the alkali quickly to about 2 cm3 before the rough value, then drop by drop until one drop makes the colour change. Record the final reading and work out the titre. Repeat until there are at least two titres within 0.10 cm3 of each other and take the mean of these.
Marking points (any 6, with the method in a logical order)
Pipette 25.0 cm3 of acid into a conical flask
Add a few drops of a suitable indicator
Fill the burette with potassium hydroxide; read the start volume
Add alkali while swirling, on a white tile
Add drop by drop near the end point until the colour changes
Record the final reading; titre = final - start
Rough titration first
Repeat to get concordant titres (within 0.10 cm3) and find the mean
Goggles worn / pipette filler used
How it is marked
5-6 marks: a full, logical plan using a pipette and burette correctly, with an indicator, careful dropwise end point and repeats to concordant results that are averaged.
3-4 marks: the main titration steps are there but some detail is missing, such as no concordant results or no mention of adding drop by drop.
1-2 marks: some correct equipment or one or two steps named, but no clear method that would give a reliable titre.
Revision notes: the method in full
Aim: To find the volume of an acid that exactly neutralises a measured volume of an alkali, and use it to work out the concentration of the alkali.
Equipment
burette and clamp stand
25.0 cm3 volumetric pipette and pipette filler
conical flask
small funnel
white tile
dilute hydrochloric acid of known concentration
sodium hydroxide solution of unknown concentration
indicator (phenolphthalein or methyl orange)
safety goggles
Method
Rinse the pipette with a little of the sodium hydroxide solution, then use the pipette filler to measure exactly 25.0 cm3 of it into a clean conical flask.
Add a few drops of indicator to the flask and stand it on a white tile under the burette.
Rinse the burette with a little hydrochloric acid, then fill it using a funnel. Remove the funnel and let some acid run through so there is no air bubble in the tip.
Read the burette at the bottom of the meniscus, with your eye level with it, and record the start reading to the nearest 0.05 cm3.
Do a quick rough titration: add acid while swirling the flask until the indicator changes colour, and note roughly how much was needed.
Refill the flask with a fresh 25.0 cm3 of alkali and indicator. Add acid quickly to within about 2 cm3 of the rough value, then add it drop by drop, swirling, until one drop makes the colour change permanently.
Record the final burette reading and subtract to find the titre.
Repeat until you have at least two titres within 0.10 cm3 of each other (concordant), then take the mean of the concordant titres.
Variables
Independent: Not a fair-test investigation; the quantity being found is the volume of acid needed to neutralise the alkali.
Dependent: The titre: the volume of acid added from the burette until the indicator changes colour (final reading minus start reading).
Control: Volume of alkali measured with the pipette (25.0 cm3); Concentration of the acid; Same indicator and number of drops each time; Same end point colour each time
Hazards
Hazard
What could happen
How to reduce the risk
Sodium hydroxide solution
Irritant or corrosive to the eyes and skin
Wear safety goggles; wash splashes off with plenty of water
Filling the burette above head height
Acid splashing into the eyes or overflowing
Take the burette down or fill it below eye level using a funnel, slowly
Using the pipette
Swallowing the solution
Always use a pipette filler, never your mouth
Key points
Concordant titres are within 0.10 cm3 of each other; only these go into the mean, never the rough titre.
Burette readings are recorded to 2 decimal places, ending in 0 or 5.
The pipette measures the alkali; the burette adds the acid. Do not mix them up.
Swirl the flask and add the acid drop by drop near the end point.
Read the bottom of the meniscus at eye level.
Moles = concentration x volume in dm3: divide cm3 by 1000 first.
Every question and data set here is original and written by Robinson Tuition. Aligned to AQA GCSE Chemistry 8462 only (not Combined Science); this is not an exam-board paper and is not endorsed by AQA.